Pololu

Step-Down Voltage Regulator 3.3V, 300mA - D24V3F3

(No reviews yet) Write a Review
SKU:
PPPOL2097
  • Step-Down Voltage Regulator 3.3V, 300mA - D24V3F3 Included Hardware
  • Step-Down Voltage Regulator 3.3V, 300mA - D24V3F3 front
  • Step-Down Voltage Regulator 3.3V, 300mA - D24V3F3
  • Step-Down Voltage Regulator 3.3V, 300mA - D24V3F3 on a breadboard
£7.80

Description

Step-Down Voltage Regulator 3.3V, 300mA - Pololu 2097

This compact (0.4″ × 0.5″) D24V3F3 switching step-down (or buck) voltage regulator takes an input voltage between 4.3 V and 42 V and efficiently reduces it to 3.3 V while allowing for a maximum output current of 300 mA. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perf-boards.

These buck (step-down) voltage regulators generate lower output voltages from input voltages as high as 42 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical efficiency between 80% to 90%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. This regulator is available with a fixed 3.3 V, 5 V, 9 V, or 12 V output, and two versions are available for each voltage, one with a 300 mA maximum output current (D24V3Fx) and one with a 600 mA maximum output current (D24V6Fx):

The regulator has short-circuit protection, and thermal shutdown prevents damage from overheating. The board does not have reverse-voltage protection.

Features:

  • Input voltage: [output voltage + dropout voltage] to 42 V (see below for more information on dropout voltage)
  • Fixed 3.3 V, 5 V, 9 V, or 12 V output (depending on regulator version) with 4% accuracy
  • Maximum output current: 300 mA or 600 mA (depending on regulator version)
  • 550 kHz switching frequency
  • 2 mA typical no-load quiescent current (20 μA typical quiescent current with SHDN = LOW)
  • Integrated over-temperature and over-current shutoff
  • Small size: 0.5″ × 0.4″ × 0.1″ (13 mm × 10 mm × 3 mm)

Using the Regulator

Connections:

PPPOL2097_3.3V_Step-Down_Voltage_Regulator_Connections2
The buck regulator has four connections: shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).

The SHDN pin can be driven low (under 0.3 V) to turn off the output and put the board into a low-power state that typically draws 20 μA, and it can be driven high (above 2.3 V) to enable the board. If you do not need to use the shutdown feature, the SHDN pin can be directly connected to VIN to permanently enable the board. You should not leave this pin disconnected as this can result in unpredictable behaviour.

The input voltage, VIN, should exceed VOUT by at least the regulator’s dropout voltage (see below for graphs of dropout voltages as a function of the load), and you must ensure that noise on your input does not exceed the 42 V maximum.

Additionally, please be wary of destructive LC spikes (see below for more information).

The output voltage, VOUT, is fixed and depends on the regulator version: the D24VxF3 version outputs 3.3 V, the D24VxF5 version outputs 5 V, the D24VxF9 version outputs 9 V, and the D24VxF12 version outputs 12 V.

The four connections are labelled on the backside of the PCB, and they are arranged with a 0.1″ spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 4×1 straight male header strip or the 4×1 right-angle male header strip that is included.
PPPOL2097_3.3V_Step-Down_Voltage_Regulator_Included_Hardware

Typical Efficiency and Output Current:


The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, this switching regulator typically has an efficiency of 80% to 90%.
PPPOL2097_3.3V_Step-Down_Voltage_Regulator_Typical_Efficiency_Graph

Note that the above graph applies to both the 300 mA and 600 mA versions, which is why the x axis extends to 600 mA. You should not expect to get more than 300 mA from the 300 mA versions (D24V3Fx).

Typical Dropout Voltage:


The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. The following graph shows the dropout voltages for the D24VxF3 regulators as a function of the output current:
PPPOL2097_3.3V_Step-Down_Voltage_Regulator_Dropout_Voltage_Graph
Note that the above graph applies to both the 300 mA and 600 mA versions, which is why the x axis extends to 600 mA. You should not expect to get more than 300 mA from the 300 mA versions (D24V3Fx).

LC Voltage Spikes:


When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (42 V), the regulator can be destroyed.

In our tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 42 V. If you are connecting more than 20 V or your power leads or supply has high inductance, we recommend soldering a 33μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 50 V.

More information about LC spikes can be found in our application note.

Dimensions:

  • Size:  10.2 mm x 12.7 mm x 0.25 mm(0.4″ × 0.5″ × 0.1″)1
  • Weight: 0.5 g1

voltage regulator dimension

General specifications:

  • Minimum operating voltage: 3.8 V2
  • Maximum operating voltage: 42 V
  • Maximum output current: 300 mA
  • Output voltage: 3.3 V
  • Reverse voltage protection?: N
  • Maximum quiescent current: 2 mA3

Notes:

  • 1 - Without included optional headers.
  • 2 - For small loads; input voltage must be at least 4.3 V to get the full 300 mA output.
  • 3 - While enabled (SHDN = HIGH) with no load. Current draw is approximately 20 µA when SHDN = LOW.
View AllClose

Additional Information

Brand:
Pololu
Part Number:
2097
Barcode:
5055421068271
View AllClose