Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range

(No reviews yet) Write a Review
  • Pololu step down  voltage regulator
  • Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range
  • Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range
  • Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range on breadboard
  • Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range on breadboard
£4.96 - £6.00

Description

Pololu Step-Down Voltage Regulator Fixed Output - D24V5Fx Range

The D24V5x family of 500 mA synchronous buck (step-down) voltage regulators generates lower output voltages from input voltages as high as 36 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters), which makes them much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators have very low drop-out voltages.


The regulators feature short-circuit/over-current protection, and thermal shutdown helps prevent damage from overheating. The boards do not have reverse-voltage protection.


This family consists of eight fixed-output versions ranging from 1.8 V to 15 V:

    • D24V5F1: Fixed 1.8V output
    • D24V5F2: Fixed 2.5V output
    • D24V5F3: Fixed 3.3V output
    • D24V5F5: Fixed 5V output
    • D24V5F6: Fixed 6V output
    • D24V5F9: Fixed 9V output
    • D24V5F12: Fixed 12V output
    • D24V5F15: Fixed 15V output

Technical Specifications

  • Input voltage:
    • 3 V to 36 V for output voltages of 1.8 V and 2.5 V
    • [output voltage + dropout voltage] to 36 V for output voltages of 3.3 V and higher (see below for more information on dropout voltage)
  • Fixed 1.8 V, 2.5 V, 3.3 V, 5 V, 6 V, 9 V, 12 V, or 15 V output (depending on regulator version) with 4% accuracy
  • Maximum output current: 500 mA
  • Typical efficiency of 80% to 93%
  • 500 kHz switching frequency (when not in power-save mode)
  • 200 μA typical no-load quiescent current
  • Over-current and short-circuit protection, over-temperature shutoff
  • Small size: 0.5″ × 0.4″ × 0.1″ (13 mm × 10 mm × 3 mm)
 


The buck regulator has four connections: shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).


The SHDN pin can be driven low (under 0.4 V) to turn off the output and put the board into a low-power state. There is a 100 kΩ pull-up resistor between the SHDN pin and VIN, so if you want to leave the board permanently enabled, the SHDN pin can be left disconnected. While the SHDN pin is being driven low, the current draw of the regulator is dominated by the current through the pull-up resistor and will be proportional to the input voltage. (At 36 V in it will draw about 360 μA.)


The input voltage, VIN, powers the regulator. Voltages between 3 V and 36 V can be applied to VIN, but for versions of the regulator that have an output voltage higher than 3 V, the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of dropout voltages as a function of the load). Additionally, please be wary of destructive LC spikes (see below for more information).
The output voltage, VOUT, is fixed and depends on the regulator version: the D24V5F1 version outputs 1.5 V, D24V5F2 version outputs 2.5 V, the D24V5F3 version outputs 3.3 V, the D24V5F5 version outputs 5 V, the D24V5F6 version outputs 6 V, the D24V5F9 version outputs 9 V, the D24V5F12 version outputs 12 V, and the D24V5F15 version outputs 15 V
The four connections are labeled on the back side of the PCB and are arranged with a 0.1″ spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 4×1 straight male header strip or the 4×1 right-angle male header strip that is included.
 

 
D24V5Fx Step-Down Voltage Regulators

Step-Down Voltage Regulator D24V5FX, with included hardware.

Typical efficiency and output current


The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. This family of switching regulators typically has an efficiency of 80% to 95%, though the actual efficiency in a given system depends on input voltage, output voltage, and output current. See the efficiency graph near the bottom of this page for more information.
In order to achieve a high efficiency at low loads, this regulator automatically goes into a power-save mode where the switching frequency is reduced. In power-save mode, the switching frequency of the regulator changes as necessary to minimize power loss. This could make it harder to filter out noise on the output caused by switching.

Typical dropout voltage


The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. Generally speaking, the dropout voltage increases as the output current increases. See the “Details” section below for more information on the dropout voltage for this specific regulator version.

LC voltage spikes


When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (36 V), the regulator can be destroyed. In our tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 36 V.

If you are connecting more than 20 V or your power leads or supply has high inductance, we recommend soldering a 33 μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 50 V.

Step-Down Regulator D24V5Fx Documents

Pololu 500mA Step-Down Voltage Regulator D24V5Fx schematic diagram (163k pdf)
Printable schematic diagram for the D24V5Fx family of Pololu 500 mA step-down voltage regulators: D24V5F1, D24V5F2, D24V5F3, D24V5F5, D24V5F6, D24V5F9, D24V5F12, and D24V5F15.
Intersil ISL85415 regulator datasheet (1MB pdf)
Dimension diagram of the D24V5Fx Step-Down Voltage Regulator (3MB step)
3D model of the D24V5Fx Step-Down Voltage Regulator (241k pdf)
Drill guide for Pololu 500mA Step-Down Voltage Regulator D24V5Fx (20k dxf)
This DXF drawing shows the locations of all of the holes for the D24V5Fx family of Pololu 500 mA step-down voltage regulators: D24V5F1, D24V5F2, D24V5F3, D24V5F5, D24V5F6, D24V5F9, D24V5F12, and D24V5F15.
 
View AllClose

Additional Information

Brand:
Pololu
Part Number:
2842
SKU:
PPPOL2842
View AllClose