Pololu Step-Down Voltage Regulator Fixed Output - D36V28Fx Range

(No reviews yet) Write a Review
  • Photon Weather Shield - SparkFun DEV-13674 main
  • Photon Weather Shield - SparkFun DEV-13674 main 1
£16.00 - £17.00

Description

Pololu Step-Down Voltage Regulator Fixed Output - D36V28Fx Range

The D36V28Fx range of buck (step-down) voltage regulators generates lower output voltages from input voltages as high as 50 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters), which makes them much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators can typically support continuous output currents between 2 A and 4 A, depending on the input voltage and output voltage (see the Maximum continuous output current section below). In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases.

This range includes six versions with fixed output voltages ranging from 3.3 V to 12 V:

  • D36V28F3: Fixed 3.3V output
  • D36V28F5: Fixed 5V output
  • D36V28F6: Fixed 6V output
  • D36V28F7: Fixed 7.5V output
  • D36V28F9: Fixed 9V output
  • D36V28F12: Fixed 12V output

The regulators have reverse voltage protection up to 40 V, output undervoltage and overvoltage protection, over-current protection, and short-circuit protection. A thermal shutdown feature also helps prevent damage from overheating and a soft-start feature limits the inrush current and gradually ramps the output voltage on startup.

Connections

Pololu Step-Down Voltage Regulator Fixed Output D36V28Fx Range Pinouts
The “power good” indicator,
PG, is an open-drain output that goes low when the regulator’s output voltage either rises more than 20% above or falls more than 10% below the nominal voltage (with hysteresis). An external pull-up resistor is required to use this pin.This regulator has six connections: power good (PG), enable (EN), input voltage (VIN), output voltage (VOUT), and two ground (GND) connections.

The EN pin is pulled-up to reverse-protected VIN by a 100 kΩ resistor, which enables the regulator’s output by default. The EN pin can be driven low (under 0.4 V) to put the board into a low-power state. The quiescent current draw in this sleep mode is dominated by the current in the pull-up resistor from EN to VIN and by the reverse-voltage protection circuit, which altogether will draw between 10 µA and 20 µA per volt on VIN when EN is held low. If you do not need this feature, you can leave the EN pin disconnected.

The input voltage, VIN, powers the regulator. Voltages between 4.5 V and 50 V can be applied to VIN, but generally the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of the dropout voltage as a function of the load).

VOUT is the regulated output voltage.

The six connections are arranged on 0.1″ grid for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. The PG connection is the only one not located along the edge of the board. A 6×1 straight male header strip and a 5×1 right-angle male header strip are is included with the regulator; one pin of the straight header can optionally be broken off and soldered into PG.

During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.

View AllClose

Additional Information

Brand:
Pololu
Part Number:
3781
SKU:
PPPOL3781
Barcode:
5055421001896
View AllClose